The Big Rig

Got my scangauge today now just got to work out how to use it

http://www.gizmodo.com.au/2012/07/this-weeks-top-web-comedy-video-the-dark-knight-and-60s-robin/

Cheers

Ray

Agreed,

That is just sad.


I am a 'conscientious objector' to dole bluggers and are of the belief that all should work hard, therefore it is unfair that I can not get handouts from the government.

your dipstick snapped?? wtf

Strange, not all Torx head screws holding the MAF in place have the pin, mine didn't and the replacement screws that came with the new MAF didn't either, but I know of another GUII that has it.
Anyway it's a number 20 torx bit and be a bit careful when reinstalling as the thread is not that hard to strip.

pfft keep dreaming lol we are not going anywhere

its "upper middle creek road" yinnar south. near the hippy house.
http://maps.google.c...sp=1&sz=19&z=17

livingston track has some nice tracks off it, morwell river road up the top around the prison farm, and further south are good.
that is where this is from.

Obviously you can't believe everything you read on the internet

Wheel studs are the same, depending on what rims you go will determine whether you need to change wheel nuts. I am running a set of steelies that use the factory nuts.

Twas me, your welcome

I used battery worlds crimper - it's about 2.5 feet long big heavy mother!

Ray, got this news yet?

Don't tell me, you're buying a 4.2!

Or maybe it's a forum takeover and you have done a deal with terry ???

You going to work for chipTwit???



I better not say any more in case I get in trouble for going too far and creating rumours again.

Well I want that one not the other one LOL :)

Just go a duramax the power to weight ratio would be sweet

Drove to Melbourne to clear a few outstanding issues and used it to test some tuning mods to my diesel chip. Diesel chip outcomes very good. Melbourne is a bigger shit hole than ever. Only one in ten people in Melbourne should be allowed to drive, anywhere.

Cheer

Ray

Hi Guys i will attempt to throw up as much detail as i can.
This is the table i made for my GUII. Should be same for other models but double check sizes first.
Being stainless means it is easy to keep clean, and you can also put hot things striaght onto it if need (billy, camp oven, pots etc)
I use it as a chopping board and everything.

Materials
1.2mm stainless splashback 865mm x 420mm(got from sheet metal place)
1.2mm stainless table 820mm x 415mm with 7mm folded and welded edge (got from sheetmetal place)
1 peice of 7mm ply 900mm x 450mm (trimmed to fit under table)
Contact adhesive
1 Piano hinge ( i used stainless one)
Marine carpet to cover ply
2 wire eye straps
1.2mm stainless leader wire (got from BCF)
Wire crimps (got from BCF)
1 Latch (as in pictures)
Rivits.

Tools
Screwdrivers
Grinder with thin cutting blade
Rivit gun
Drill
Paint brush (cheap)
Circular saw
Stanley Knife
Pliers or crimpers

Now i apologise that i do not have any pics of me actually making this, don't think about this till after. I did get a few midway though.

Cut plywood to size to fit on underside of table and glue in with contact adhesive. I clamped it and sat weight on it overnight till it dried.
Drill 3mm hole in edge in prep for wire stays later

When that is done cover ply with marine carpet.

Remove plastic trim at top off door.
Remove door trim if you wish and to look at were wires etc are.( I fitted my splashback over the door trim as it the slashback doesnt cover the whole door. about 40mm short at the bottom, so when table is fitted it does not foul on pinch mould when door is closed.

Hold Splashback into postion and mark the top righthand edge to trim off with the grinder. (edge of door angles back in)

Once back is cut and happy with where it will sit on door( Mine is **mm short from bottom and sits just high enough that the plastic trim when refitted will sit over the top edge),

attach the hinge to the "Table" side first.

I wanted it so you didn't see the hinge, so all you see is the knuckle. So the hinge is fitted to the table through the back egde with rivits. It is fiddly as you only have 7 mm to work with.
Once done, Hold the splash back under hinge and mark holes piano hinge and drill. (only as many fixings as you wish. I did every hole)
Fit slashback to door using only a couple off rivits at top to start with.
Then you can fit table and hinge to bottom of splash back. You want the hinge to go behind the splash back, and attach with rivits in 2 holes only. You can do all rivits once all fitted and fit splashback to door. (i used 3 rivets down each side and a few across the top

Have a piece of timber to support table

With the top trim still off you want to fit these to top of door frame with rivits

and cut slots in trim where needed and mark holes for latch (i put thin peice of ali on back of trim for something the screws could bit into) and refit. Attach leader wire to table using crimp and feed though eye at top at fit off a required length with crimp

Close top and fit latch to bottom of table


Finished Product




I also fitted LED Strip to around top of door frame before i did the table.

ENJOY


Cheers olly
Hope you can all make sense of all that scribble.

Found time to test out the winch and land anchor..

Works well, winch is noisy though..





Filled all the holes back in after getting some weird looks from the neighbors.



Sent from my Galaxy Nexus using Tapatalk 2

Maybe he and his wife just want more kids and would like to be able to give them a normal childhood?
If that ends up being the case then I take my hat off to him.
I think far from being boring he has shown time and time again that he is man who is always willing to stand up for his convictions, whether popular or not.

I think I'm addicted to like this buttons

I'm greatful for this forum..I like it here...
I'm truly amazed at the out come of my member ship of the other site.

I don't see any issue with copy a thread that you started especially if its a guide. Could always just re word it ...we don't need any info from there as it will build itself here anyway.

Dan

I think I'm addicted to like this buttons

like me, like me

hahahahahahahahaha



casts nicely ...



STRIKE ... got one

we start with zero ... I hope

The only thing missing is the Jim Beam.

Cheers

Ray